MATERIAL SAFETY DATA SHEET
DOW CORNING ANTIFOAM 1410, 1520 - US, LIQUID
3. HAZARDS IDENTIFICATION
Low hazard for usual industrial or commercial handling. High vapour concentrations may cause
drowsiness. See "Other Health Effects" Section. Can decompose at high temperatures forming toxic
gases. Contents may develop pressure on prolonged exposure to heat.
EMERGENCY OVERVIEW:
POTENTIAL HEALTH EFFECTS
Contact with mist or spray may cause irritation of mucous membranes, coughing and difficulty in
breathing. See "Other Health Effects" Section.
Inhalation:
Prolonged, confined (especially under the finger nails, under rings or watch bands) or repeated
exposure may cause skin irritation. May cause defatting, drying and cracking of the skin. Prolonged and
repeated contact may lead to dermatitis.
Skin Contact:
A single, prolonged skin exposure is not likely to result in the absorption of toxic amounts of the material.
Skin Absorption:
Splashes to the eye may cause irritation, redness and pain.
Eye Contact:
Ingestion is not a likely route of exposure. This product may cause mild gastrointestinal discomfort.
Ingestion:
Effects (irritancy) on the skin and eyes may be delayed, and damage may occur without the sensation
or onset of pain. Strict adherence to first aid measures following any exposure is essential.
Other Health Effects:
EMERGENCY TELEPHONE NUMBERS (FOR EMERGENCIES INVOLVING CHEMICAL SPILLS OR RELEASE)
Toronto, ON (416) 226-6117 Montreal, QC (514) 861-1211 Winnipeg, MB (204) 943-8827
Edmonton, AB (780) 424-1754 Calgary, AB (403) 263-8660 Vancouver, BC (604) 685-5036
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Brenntag Canada Inc.
43 Jutland Rd.
Toronto, ON
M8Z 2G6
(416) 259-8231
Website: http:\\www.brenntag.ca
WHMIS#:
00062411
Index:
2008 March 13
PRODUCT IDENTIFICATION
Dow Corning Antifoam 1410, 1520 - US, Liquid.
Product Name:
2008 March 13
Date of Revision:
Effective Date:
HCI1268/08A
Not available.
Chemical Name:
Dow Corning Antifoam 1520 - US; D/C 1410 Antifoam Emulsion.
Synonyms:
Silicone Emulsion.
Chemical Family:
Not applicable.
Molecular Formula:
Antifoam agent.
Product Use:
WHMIS Classification / Symbol:
READ THE ENTIRE MSDS FOR THE COMPLETE HAZARD EVALUATION OF THIS PRODUCT.
Not WHMIS Regulated.
Ingredient
CAS#
ACGIH TLV
% Concentration
2. COMPOSITION, INFORMATION ON INGREDIENTS (Not Intended As Specifications)
Dimethylpolysiloxane
63148-62-9
---
15 - 40
Dow Corning Antifoam 1410, 1520 - US, Liquid
Brenntag Canada Inc.
Date of Revision:
2008 March 13
WHMIS Number :
00062411
Page 2 of 6
4. FIRST AID MEASURES
FIRST AID PROCEDURES
Move victim to fresh air. Give artificial respiration ONLY if breathing has stopped. Give
cardiopulmonary resuscitation (CPR) if there is no breathing AND no pulse. Obtain medical attention
IMMEDIATELY.
Inhalation:
Start flushing while removing contaminated clothing. Wash affected areas thoroughly with soap and
water. If irritation, redness, or a burning sensation develops and persists, repeat flushing and obtain
medical attention.
Skin Contact:
Immediately flush eyes with running water for a minimum of 20 minutes. Hold eyelids open during
flushing. If irritation persists, repeat flushing. Obtain medical attention IMMEDIATELY.
Eye Contact:
Do not attempt to give anything by mouth to an unconscious person. If victim is alert and not
convulsing, rinse mouth out and give 1/2 to 1 glass of water to dilute material. IMMEDIATELY contact
local Poison Control Centre. Vomiting should only be induced under the direction of a physician or a
poison control centre. If spontaneous vomiting occurs, have victim lean forward with head down to
avoid breathing in of vomitus, rinse mouth and administer more water. IMMEDIATELY transport victim
to an emergency facility.
Ingestion:
This product contains materials that may cause severe pneumonitis if aspirated. If ingestion has
occurred less than 2 hours earlier, carry out careful gastric lavage; use endotracheal cuff if available, to
prevent aspiration. Observe patient for respiratory difficulty from aspiration pneumonitis. Give artificial
resuscitation and appropriate chemotherapy if respiration is depressed.
Medical conditions that may be aggravated by exposure to this product include diseases of the skin,
eyes or respiratory tract.
Note to Physicians:
5. FIRE-FIGHTING MEASURES
Flashpoint (°C)
AutoIgnition
Temperature (°C)
LEL
UEL
Flammability Limits in Air (%):
> 101. (3)
Not available.
Not available.
Not available.
Not regulated.
Flammability Class (WHMIS):
Thermal decomposition products are toxic and may include formaldehyde, oxides of silicon, carbon and
irritating gases.
Hazardous Combustion
Products:
Closed containers exposed to heat may explode. Spilled material may cause floors and contact
surfaces to become slippery.
Unusual Fire or Explosion
Hazards:
Not expected to be sensitive to mechanical impact.
Sensitivity to Mechanical Impact:
Not available.
Rate of Burning:
Not available.
Explosive Power:
Not expected to be sensitive to static discharge.
Sensitivity to Static Discharge:
EXTINGUISHING MEDIA
Use carbon dioxide or dry chemical media for small fires. If only water is available, use it in the form of
a fog.
Fire Extinguishing Media:
FIRE FIGHTING
INSTRUCTIONS
Isolate materials that are not involved in the fire and protect personnel. Cool containers with flooding
quantities of water until well after the fire is out. Spilled material may cause floors and contact surfaces
to become slippery.
Instructions to the Fire Fighters:
Use self-contained breathing apparatus and protective clothing.
Fire Fighting Protective
Equipment:
6. ACCIDENTAL RELEASE MEASURES
Information in this section is for responding to spills, leaks or releases in order to prevent or minimize the adverse effects on persons,
property and the environment. There may be specific reporting requirements associated with spills, leaks or releases, which change from
region to region.
Dow Corning Antifoam 1410, 1520 - US, Liquid
Brenntag Canada Inc.
Date of Revision:
2008 March 13
WHMIS Number :
00062411
Page 3 of 6
In all cases of leak or spill contact vendor at Emergency Number shown on the front page of this MSDS.
Spilled material may cause floors and contact surfaces to become slippery. Wear protective clothing.
Collect product for recovery or disposal. For release to land, or storm water runoff, contain discharge
by constructing dykes or applying inert absorbent; for release to water, utilize damming and/or water
diversion to minimize the spread of contamination. Ventilate enclosed spaces. Notify applicable
government authority if release is reportable or could adversely affect the environment.
Containment and Clean-Up
Procedures:
7. HANDLING AND STORAGE
HANDLING
Use normal "good" industrial hygiene and housekeeping practices. Containers exposed to heat may be
under internal pressure. These should be cooled and carefully vented before opening. A face shield
and apron should be worn. Vent container frequently, and more often in warm weather, to relieve
pressure.
Handling Practices:
See Section 8, "Engineering Controls".
Ventilation Requirements:
Use only with adequate ventilation and avoid breathing vapours and aerosols. Avoid contact with eyes,
skin or clothing. Wash thoroughly with soap and water after handling. Wash contaminated clothing
thoroughly before re-use.
Other Precautions:
STORAGE
20 to 40 °C. (3)
Storage Temperature (°C):
General exhaust is acceptable.
Ventilation Requirements:
Store in a cool, well-ventilated area. Keep away from heat, sparks and flames. Keep containers
closed. Do not expose sealed containers to temperatures above 40° C. Avoid moisture contamination.
Protect from direct sunlight. Protect against physical damage.
Storage Requirements:
Confirm suitability of any material before using.
Special Materials to be Used for
Packaging or Containers:
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Recommendations listed in this section indicate the type of equipment, which will provide protection against overexposure to this
product. Conditions of use, adequacy of engineering or other control measures, and actual exposures will dictate the need for specific
protective devices at your workplace.
ENGINEERING CONTROLS
General exhaust is acceptable. Local exhaust ventilation preferred. Make up air should be supplied to
balance air that is removed by local or general exhaust ventilation. Ventilate low lying areas such as
sumps or pits where dense vapours may collect.
Engineering Controls:
PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Safety glasses with side shields are recommended as minimal eye protection. Use chemical safety
goggles when there is potential for eye contact. Contact lenses should not be worn when working with
this material.
Eye Protection:
Gloves and protective clothing made from PVC should be impervious under conditions of use. Prior to
use, user should confirm impermeability. Discard contaminated gloves.
Skin Protection:
No specific guidelines available. Respiratory protection should not be necessary unless a mist is
created. A NIOSH/MSHA-approved air-purifying respirator equipped with 1 000 ppm organic vapours.
An air-supplied respirator if concentrations are higher or unknown.
If while wearing a respiratory protection, you can smell, taste or otherwise detect anything unusual, or in
the case of a full facepiece respirator you experience eye irritation, leave the area immediately. Check
to make sure the respirator to face seal is still good. If it is, replace the filter, cartridge or canister. If
the seal is no longer good, you may need a new respirator. (4)
Respiratory Protection:
Wear an impermeable apron and boots. Locate safety shower and eyewash station close to chemical
handling area. Take all precautions to avoid personal contact.
Other Personal Protective
Equipment:
None established for this product.
EXPOSURE GUIDELINES
9. PHYSICAL AND CHEMICAL PROPERTIES (Not intended as Specifications)
Dow Corning Antifoam 1410, 1520 - US, Liquid
Brenntag Canada Inc.
Date of Revision:
2008 March 13
WHMIS Number :
00062411
Page 4 of 6
Liquid.
Off-white.
Mild odour.
Not available.
65. (3)
Not available.
Not available.
Not available.
1.0. (3)
1 000 kg/m3.
5 000 cSt. (3)
Not applicable.
Not available.
Not available.
3.5. (3)
Not available.
Not applicable.
Physical State:
Appearance:
Odour:
Odour Threshold (ppm):
Boiling Range (°C):
Melting/Freezing Point (°C):
Vapour Pressure (mm Hg at 20° C):
Vapour Density (Air = 1.0):
Relative Density (g/cc):
Bulk Density:
Viscosity:
Evaporation Rate (Butyl Acetate = 1.0):
Solubility:
% Volatile by Volume:
pH:
Coefficient of Water/Oil Distribution:
Volatile Organic Compounds (VOC):
11. TOXICOLOGICAL INFORMATION
TOXICOLOGICAL DATA:
SUBSTANCE
LD50 (Oral, Rat)
LD50 (Dermal, Rabbit)
LC50 (Inhalation, Rat, 4h)
Dimethylpolysiloxane
> 40 000 mg/kg (3)
> 19 400 mg/kg (4)
> 535 mg/L (3)
The ingredient(s) of this product is (are) not classed as carcinogenic by ACGIH, IARC, OSHA or NTP.
Carcinogenicity Data:
No adverse reproductive effects are anticipated.
Reproductive Data:
No adverse mutagenic effects are anticipated.
Mutagenicity Data:
No adverse teratogenic effects are anticipated.
Teratogenicity Data:
None known.
Respiratory / Skin Sensitization
Data:
None known.
Synergistic Materials:
None known.
Other Studies Relevant to
Material:
12. ECOLOGICAL INFORMATION
Not available. May be harmful to aquatic life.
Ecotoxicity:
Not available. Can be dangerous if allowed to enter drinking water intakes. Do not contaminate
domestic or irrigation water supplies, lakes, streams, ponds, or rivers.
Environmental Fate:
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY
Stable.
Under Normal Conditions:
Not normally a fire hazard. Water content of product prevents ignition. The product can support
combustion if water evaporates.
Under Fire Conditions:
Will not occur.
Hazardous Polymerization:
High temperatures, sparks, open flames and all other sources of ignition.
Conditions to Avoid:
Strong oxidizers. Lewis or mineral acids.
Materials to Avoid:
Thermal decomposition products are toxic and may include formaldehyde, oxides of silicon, carbon and
irritating gases.
Decomposition or Combustion
Products:
Dow Corning Antifoam 1410, 1520 - US, Liquid
Brenntag Canada Inc.
Date of Revision:
2008 March 13
WHMIS Number :
00062411
Page 5 of 6
13. DISPOSAL CONSIDERATIONS
None required.
Deactivating Chemicals:
This information applies to the material as manufactured. Reevaluation of the product may be required
by the user at the time of disposal since the product uses, transformations, mixtures and processes
may influence waste classification. Dispose of waste material at an approved (hazardous) waste
treatment/disposal facility in accordance with applicable local, provincial and federal regulations. Do not
dispose of waste with normal garbage, or to sewer systems.
Waste Disposal Methods:
See "Waste Disposal Methods".
Safe Handling of Residues:
Empty containers retain product residue and can be dangerous. Empty drums should be completely
drained, properly bunged and promptly returned to a drum reconditioner. Do not expose such containers
to heat, flame, sparks, static electricity, or other sources of ignition; they may explode and cause injury
or death. Treat package in the same manner as the product.
Disposal of Packaging:
14. TRANSPORTATION INFORMATION
CANADIAN TDG ACT SHIPPING DESCRIPTION:
This product is not regulated by TDG.
Label(s): Not applicable. Placard: Not applicable.
ERAP Index: -----.
Exemptions: None known.
US DOT CLASSIFICATION (49CFR 172.101, 172.102):
This product is not regulated by DOT.
Label(s): Not applicable. Placard: Not applicable.
CERCLA-RQ: Not available.
Exemptions: None known.
15. REGULATORY INFORMATION
CANADA
All constituents of this product are included on the DSL.
CEPA - NSNR:
Not included.
CEPA - NPRI:
Controlled Products Regulations Classification (WHMIS):
Not WHMIS Regulated.
USA
All constituents of this product are included on the TSCA inventory.
Environmental Protection Act:
Not regulated.
OSHA HCS (29CFR 1910.1200):
Text22:
NFPA: 0 Health, 1 Fire, 0 Reactivity (3)
Text22:
HMIS: 0 Health, 1 Fire, 0 Reactivity (6)
INTERNATIONAL
Not available.
16. OTHER INFORMATION
REFERENCES
RTECS-Registry of Toxic Effects of Chemical Substances, Canadian Centre for Occupational Health and Safety RTECS
database.
1.
Clayton, G.D. and Clayton, F.E., Eds., Patty's Industrial Hygiene and Toxicology, 3rd ed., Vol. IIA,B,C, John Wiley and Sons,
New York, 1981.
2.
Supplier's Material Safety Data Sheet(s).
3.
CHEMINFO, through "CCINFOdisc", Canadian Centre for Occupational Health and Safety, Hamilton, Ontario, Canada.
4.
Guide to Occupational Exposure Values, 2005, American Conference of Governmental Industrial Hygienists, Cincinnati, 2005.
5.
Dow Corning Antifoam 1410, 1520 - US, Liquid
Brenntag Canada Inc.
Date of Revision:
2008 March 13
WHMIS Number :
00062411
Page 6 of 6
Regulatory Affairs Group, Brenntag Canada Inc.
6.
The British Columbia Drug and Poison Information Centre, Poison Managements Manual, Canadian Pharmaceutical
Association, Ottawa, 1981.
7.
____________________________________________________________________________________________________________
The information contained herein is offered only as a guide to the handling of this specific material and has been prepared in good faith
by technically knowledgeable personnel. It is not intended to be all-inclusive and the manner and conditions of use and handling may
involve other and additional considerations. No warranty of any kind is given or implied and Brenntag Canada Inc. will not be liable for
any damages, losses, injuries or consequential damages which may result from the use of or reliance on any information contained
herein. This Material Safety Data Sheet is valid for three years.
____________________________________________________________________________________________________________
To obtain revised copies of this or other Material Safety Data Sheets, contact your nearest Brenntag Canada Regional office.
British Columbia: 20333-102B Avenue, Langley, BC, V1M 3H1
Phone: (604) 513-9009 Facsimile: (604) 513-9010
Alberta: 6628 - 45 th. Street, Leduc, AB, T9E 7C9
Phone: (780) 986-4544 Facsimile: (780) 986-1070
Manitoba: 681 Plinquet Street, Winnipeg, MB, R2J 2X2
Phone: (204) 233-3416 Facsimile: (204) 233-7005
Ontario: 43 Jutland Road, Toronto, ON, M8Z 2G6
Phone: (416) 259-8231 Facsimile: (416) 259-5333
Quebec: 2900 Jean Baptiste Des., Lachine, PQ, H8T 1C8
Phone: (514) 636-9230 Facsimile: (514) 636-0877
Atlantic: A-105 Akerley Boulevard, Dartmouth, NS, B3B 1R7
Phone: (902) 468-9690 Facsimile: (902) 468-3085
____________________________________________________________________________________________________________
Prepared By: Regulatory Affairs Group, Brenntag Canada Inc., (416) 259-8231.