Upgrade your CNC machines with our refurbished and remanufactured parts, designed to meet or exceed new standards. Ensure peak performance and reliability for your equipment. Download the Fadal Drawbar and Pilot Kits Instruction Manual today from ITSCNC for detailed guidance. Trust ITSCNC for quality parts and expert support to keep your machines running efficiently!
About ITSCNC
At itscnc.com, we provide all kinds of CNC machine parts and repair services, first-class product quality, perfect sales service, and fast delivery at affordable prices. With our training team of experienced applications experts, we will ensure you get the most out of your machines. We offer a wide variety of parts designed to fit your Fadal like circuit boards, Rotary Parts, USB Mass Storage, Axis Amplifier, Circuit Components, Ballscrews, Fadal Spindle, circuit board, etc.
Call at 1-800-342-3475 or mail at parts@itscnc.com, you will find yourself working in a true partnership that results in an incredible experience, and an end product that is the best.
Tag Cloud
20701 Plummer St.
Chatsworth, CA 91311
859-534-4600
www.maint-tech.com
DRB-0090 DRAWBAR/PILOT KIT, COOLANT-THRU-SPINDLE SYSTEMS
1. Remove original Drawbar, and Belleville stack.
2. Clean sidewall in pocket so washer can seal against sidewall at bottom of pocket. A Brake Cylinder Hone
could be helpful to do this.
3.
Install HDW-0158 and HDW-0150 O’Rings onto DRB-0109 Sealing Washer with DOW 111 grease.
4.
Insert Sealing Washer SIDEWAYS into opening [see photo].
5.
Insert Drawbar up from bottom, and through hole in washer. Guide Drawbar through center O’Ring, and
press Washer down to bottom of pocket.
6. This design washer allows Coolant-Thru fluid pressure to lift Sealing Washer without damaging O’Ring on
bottom of the original design washer.
DRAWBAR and PILOT KITS - Rev B
May 1, 2009
HDW-0158 O’Ring is not
needed on Spring Pilot
when DRB-0109 Sealing
Washer
is
installed at
bottom. It is not included in
this kit.
INSTALLATION OF DRB-0109 SEALING WASHER IN COOLANT-THRU SPINDLES
Machines fitted with Locking Drawbar
mechanisms and Fadal Coolant-Thru-
Spindle systems use this kit. The HDW-
0195 Belleville Spring kit
[ordered
separately] is installed with DRB-0109
Sealing Washer at the bottom of the
pocket.
Any DRB-0074 spacers
that were
previously
installed underneath
the
Orientation Bridge
legs must be
removed.
The new DRB-0092 Knock-Out Cap is
improved to allow the black tungsten
carbide seal face to pivot better.
HDW-0195 BELLEVILLES:
Short Pocket: 4.325 inch [109.86 mm] is 38 Springs
Long Pocket: 4.627 Inch
[117.5 mm] is 42 Springs
HDW-0158
HDW-0177
20701 Plummer St.
Chatsworth, CA 91311
859-534-4600
www.maint-tech.com
DRB-0091 DRAWBAR/PILOT KIT, NON-COOLANT-THRU-SPINDLE SYSTEMS
Machines fitted with Locking Drawbar mechanisms and have no coolant-thru system use this kit. The HDW-
0195 Belleville Spring kit [ordered separately] are installed with DRB-0068 Knock-Out Cap. The included
DRB-0074 spacers are installed underneath the Orientation Bridge legs to raise the Bridge .070 inch.
DRB-0030 DRAWBAR/PILOT KIT NON-LOCKING
Machines fitted with Non-Locking Drawbars in either 6500, 7500, 8000, 10000 or 15000 RPM configurations
use this kit to replace Drawbar, with HDW-0195 [ordered separately] Belleville Springs. Use 47 springs if the
manufacturing mark exists on the bottom of the long spindle key, and 44 if not marked.
Short Pocket: 4.325 [109.86mm] 44 Springs
Long Pocket: 4.627 [117.53mm] 47 Springs
Non-Locking Drawbars will not have the DRB-
0109 Sealing Washer installed as the Coolant-
Thru-Spindle systems are not installed on
Non-Locking Drawbar Spindles.
DRB-0109 Sealing Washer
is not needed on NON-
Coolant-Thru systems.
Short Pocket: 4.325 inch
[109.86 mm] is 40 Springs
Long Pocket: 4.627 Inch
[117.5 mm] is 44 Springs