MATERIAL SAFETY DATA SHEET
TRIETHYLENE GLYCOL INHIBITED TO 5 % CFT1755CW
3. HAZARDS IDENTIFICATION
Corrosive! Toxic effects are principally related to its corrosive properties. Causes skin and eye burns.
Mists or sprays are extremely irritating to eyes and respiratory tract. May cause skin sensitization or
other allergic responses. See "Other Health Effects" Section. Can decompose at high temperatures
forming toxic gases. Contents may develop pressure on prolonged exposure to heat.
EMERGENCY OVERVIEW:
POTENTIAL HEALTH EFFECTS
At normal temperatures : Corrosive! Inhalation is not a likely route of exposure at normally
encountered temperatures. Product may cause severe irritation of the nose, throat and respiratory
tract. Repeated and/or prolonged exposures may cause productive cough, running nose,
bronchopneumonia, pulmonary oedema (fluid build-up in lungs), and reduction of pulmonary function.
At elevated temperatures : Vapours are extremely irritating to eyes and respiratory tract.
Inhalation:
EMERGENCY TELEPHONE NUMBERS (FOR EMERGENCIES INVOLVING CHEMICAL SPILLS OR RELEASE)
Toronto, ON (416) 226-6117 Montreal, QC (514) 861-1211 Winnipeg, MB (204) 943-8827
Edmonton, AB (780) 424-1754 Calgary, AB (403) 263-8660 Vancouver, BC (604) 685-5036
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Brenntag Canada Inc.
43 Jutland Rd.
Toronto, ON
M8Z 2G6
(416) 259-8231
Website: http:\\www.brenntag.ca
WHMIS#:
00063338
Index:
2007 September 07
PRODUCT IDENTIFICATION
Triethylene Glycol Inhibited to 5 % CFT1755CW.
Product Name:
2007 September 07
Date of Revision:
Effective Date:
HCI2199/07C
Not available.
Chemical Name:
Not available.
Synonyms:
Aqueous mixture of oxygenated aliphatic hydrocarbons and Morpholine Derivatives.
Chemical Family:
Not applicable.
Molecular Formula:
Heat transfer fluid.
Product Use:
WHMIS Classification / Symbol:
READ THE ENTIRE MSDS FOR THE COMPLETE HAZARD EVALUATION OF THIS PRODUCT.
D-2B: Toxic (skin sensitizer)
E: Corrosive
Ingredient
CAS#
ACGIH TLV
% Concentration
2. COMPOSITION, INFORMATION ON INGREDIENTS (Not Intended As Specifications)
Triethylene Glycol
112-27-6
—
50 - 100
Morpholine Derivatives
Not available.
---
0.1 - 5
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 2 of 8
4. FIRST AID MEASURES
FIRST AID PROCEDURES
Prompt removal of the material and obtaining medical attention are essential for all contact. Remove all
contaminated clothing and immediately wash the exposed areas with copious amounts of water.
Continue the flushing during transportation to the emergency department. Corrosive effects may be
delayed (up to 72 hours), and damage may occur without the sensation or onset of pain. Contact local
poison control centre for further guidance.
General Guidelines:
Move victim to fresh air. Give artificial respiration ONLY if breathing has stopped. Give
cardiopulmonary resuscitation (CPR) if there is no breathing AND no pulse. Oxygen administration may
be beneficial in this situation but should only be administered by personnel trained in its use. Obtain
medical attention IMMEDIATELY.
Inhalation:
At normal temperatures : Prompt removal of the material from the skin is essential. Remove all
contaminated clothing and immediately wash the exposed areas with copious amounts of water for a
minimum of 30 minutes or up to 60 minutes for critical body areas. Obtain medical attention
IMMEDIATELY.
At elevated temperatures : See "Note to Physicians" below.
Skin Contact:
Immediately flush eyes with running water for a minimum of 30 minutes, preferably up to 60 minutes.
Hold eyelids open during flushing. If irritation persists, repeat flushing. Do not transport victim until the
recommended flushing period is completed unless flushing can be continued during transport.
Eye Contact:
Do not attempt to give anything by mouth to an unconscious person. IMMEDIATELY contact local
Poison Control Centre. If victim is alert and not convulsing, rinse mouth out and give 1 to 2 glasses of
milk. Water may be used if milk is not available but it is not as effective. If spontaneous vomiting
occurs, have victim lean forward with head down to avoid breathing in of vomitus, rinse mouth and
administer more milk or water. IMMEDIATELY transport victim to an emergency facility.
Ingestion:
At normal temperatures : Corrosive! Burns (chemical) can occur if not promptly removed. Prolonged,
confined (especially under the finger nails, under rings or watch bands) or repeated exposure may
cause skin irritation and possibly lead to (chemical) burns. Prolonged and repeated contact may lead to
dermatitis. May cause skin sensitization or other allergic responses See Section 11, "Other Studies
Relevant to Material".
At elevated temperatures : Corrosive! Burns (thermal) can occur if not promptly removed.
Skin Contact:
Skin absorption is a secondary concern to the continual destruction of tissue while the product is in
contact with the skin.
Skin Absorption:
At normal temperatures : Corrosive! This product causes immediate pain, severe burns and
permanent corneal damage which may result in blindness.
At elevated temperatures : Corrosive! Burns (thermal) can occur if not promptly removed.
Eye Contact:
Corrosive! Ingestion is not a likely route of exposure. This product causes severe burning and pain in
the mouth, throat and abdomen. Vomiting, diarrhea and perforation of the esophagus and stomach
lining may occur.
Ingestion:
Corrosive effects on the skin and eyes may be delayed, and damage may occur without the sensation
or onset of pain. Strict adherence to first aid measures following any exposure is essential.
May cause pulmonary oedema, chemical pneumonitis, liver damage, kidney damage and central
nervous system (CNS) depression. Pulmonary oedema is the build-up of fluid in the lungs that might be
fatal. Symptoms of pulmonary oedema, such as shortness of breath, may not appear until several
hours after exposure and are aggravated by physical exertion. (4) CNS depression is characterized by
headache, dizziness, drowsiness, nausea, vomiting and incoordination. Severe overexposures may
lead to coma and possible death due to respiratory failure. Liver damage is characterized by the loss of
appetite, jaundice (yellowish skin colour), and occasional pain in the upper left-hand side of the
abdomen. Signs and symptoms of kidney damage generally progress from oliguria, to blood in the
urine, to total renal failure.
Triethylene Glycol : Metabolic abnormalities can occur following ingestion and include ethanol-like
inebriation. (3)
Other Health Effects:
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 3 of 8
Immediate consultation with the local Poison Control Centre should be initiated. Severe and sometimes
delayed (up to 72 hours) local and systemic reactions can occur.
Due to the severely irritating or corrosive nature of the material, swallowing may lead to ulceration and
inflammation of the upper alimentary tract with hemorrhage and fluid loss. Also, perforation of the
esophagus or stomach may occur, leading to mediastinitis or peritonitis and the resultant complications.
(3)
This product contains materials that may cause severe pneumonitis if aspirated. If ingestion has
occurred less than 2 hours earlier, carry out careful gastric lavage; use endotracheal cuff if available, to
prevent aspiration. Observe patient for respiratory difficulty from aspiration pneumonitis. Give artificial
resuscitation and appropriate chemotherapy if respiration is depressed.
Treatment for corrosive chemical contact with skin:
1. Immerse the exposed part immediately in ice water to relieve pain and to prevent swelling and
blistering. Place cold packs, ice or wet cloths on the burned area if immersion is not possible.
2. Remove anything that is constrictive, such as rings, bracelets or footwear, before swelling begins.
3. Cover the exposed part with a clean, preferably sterile, lint-free dressing.
4. For severe exposure, immediately seek medical attention and monitor breathing and treat for shock.
Treatment for thermal, surface burns:
1. Immerse the burned part immediately in ice water to relieve pain and to prevent swelling and
blistering. Place cold packs, ice or wet cloths on the burned area if immersion is not possible.
2. Remove anything that is constrictive, such as rings, bracelets or footwear, beforeswelling begins.
3. Cover the burn with a clean, preferably sterile, lint-free dressing.
4. For severe burns, immediately seek medical attention and monitor breathing andtreat for shock.
Medical conditions that may be aggravated by exposure to this product include neurological and
cardiovascular disorders, diseases of the skin, eyes or respiratory tract, preexisting liver and kidney
disorders.
Note to Physicians:
5. FIRE-FIGHTING MEASURES
Flashpoint (°C)
AutoIgnition
Temperature (°C)
LEL
UEL
Flammability Limits in Air (%):
> 177 (Estimated)
371 (Estimated)
0.9 (Estimated)
9.2 (Estimated)
Not regulated.
Flammability Class (WHMIS):
Thermal decomposition products are toxic and may include oxides of carbon, nitrogen and irritating
gases. Heating in air may produce irritating aldehydes, acids and ketones.
Hazardous Combustion
Products:
Not normally a fire hazard. Water content of product prevents ignition. Closed containers exposed to
heat may explode. Do not direct a solid stream of foam into hot, burning pools. This may cause
spattering and increase fire intensity. Spilled material may cause floors and contact surfaces to become
slippery.
Spills on hot fibrous insulation may lead to the lowering of the autoignition temperature possibly
resulting in spontaneous combustion.
Unusual Fire or Explosion
Hazards:
Not expected to be sensitive to mechanical impact.
Sensitivity to Mechanical Impact:
Not available.
Rate of Burning:
Not available.
Explosive Power:
Expected to be sensitive to static discharge when vapours are present between the lower and upper
explosive limits.
Sensitivity to Static Discharge:
EXTINGUISHING MEDIA
Foam. Use carbon dioxide or dry chemical media for small fires. If only water is available, use it in the
form of a fog. Do not use high volume water jet.
Fire Extinguishing Media:
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 4 of 8
FIRE FIGHTING
INSTRUCTIONS
Do not use solid water streams near ruptured tanks or spills. Reacts violently with water and can
splatter onto personnel. (3) Isolate materials that are not involved in the fire and protect personnel.
Cool containers with flooding quantities of water until well after the fire is out.
Instructions to the Fire Fighters:
Use self-contained breathing apparatus and protective clothing. Protective clothing for skin and eye
protection should be worn to protect against corrosive materials.
Fire Fighting Protective
Equipment:
6. ACCIDENTAL RELEASE MEASURES
Information in this section is for responding to spills, leaks or releases in order to prevent or minimize the adverse effects on persons,
property and the environment. There may be specific reporting requirements associated with spills, leaks or releases, which change from
region to region.
See Section 13, "Deactivating Chemicals". In all cases of leak or spill contact vendor at Emergency
Number shown on the front page of this MSDS. Utilize a spill kit, if available. Wear protective clothing.
Recover spilled material on non-combustible absorbents, such as sand or vermiculite, and place in
covered containers for disposal. Use spark-resistant tools. Collect product for recovery or disposal. For
release to land, or storm water runoff, contain discharge by constructing dykes or applying inert
absorbent; for release to water, utilize damming and/or water diversion to minimize the spread of
contamination. Ventilate enclosed spaces. Notify applicable government authority if release is
reportable or could adversely affect the environment.
Containment and Clean-Up
Procedures:
7. HANDLING AND STORAGE
HANDLING
Use normal "good" industrial hygiene and housekeeping practices. Containers exposed to heat may be
under internal pressure. These should be cooled and carefully vented before opening. A face shield
and apron should be worn. When diluting, add this material/product to water in small amounts to avoid
spattering. Never add water to this material/product. The water should be lukewarm. Never start with
hot or cold water.
Handling Practices:
See Section 8, "Engineering Controls".
Ventilation Requirements:
Use only with adequate ventilation and avoid breathing vapours and aerosols. Avoid contact with eyes,
skin or clothing. Wash thoroughly with soap and water after handling. Wash contaminated clothing
thoroughly before re-use.
Sudden release of hot organic chemical vapours or mists from process equipment operating at elevated
temperature and pressure, or sudden ingress of air into vacuum equipment, may result in ignitions
without the presence of obvious ignition sources. Published "autoignition" or "ignition" temperature
values cannot be treated as safe operating temperatures in chemical processes without analysis of the
actual process conditions.
Corrosive residue is most likely to be deposited at process vents or storage tanks, especially during
filling operations. The use of compressed air to force corrosive materials from delivery trucks is of
special concern. Scrubbing the exhaust of these vents is highly recommended. Jurisdictional
regulations should be consulted to determine required practices.
Other Precautions:
STORAGE
See below.
Storage Temperature (°C):
Ventilation should be corrosion proof.
Ventilation Requirements:
Store in a clean, cool well ventilated area, away from organic chemicals, strong bases, strong acids,
metal powders, carbides, sulfides, and any readily oxidizable material. Protect from direct sunlight.
Protect against physical damage. Avoid moisture contamination. Hygroscopic. Storage area should be
equipped with corrosion-resistant floors, sumps and should have controlled drainage to a recovery tank.
Storage Requirements:
Materials of construction for storing the product include: steel. Solutions are slightly corrosive to
metals. Aluminum and its alloys should not be used in equipment for storage, handling or
transportation. Confirm suitability of any material before using.
Special Materials to be Used for
Packaging or Containers:
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Recommendations listed in this section indicate the type of equipment, which will provide protection against overexposure to this
product. Conditions of use, adequacy of engineering or other control measures, and actual exposures will dictate the need for specific
protective devices at your workplace.
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 5 of 8
ENGINEERING CONTROLS
General exhaust is acceptable. Local exhaust ventilation preferred. Ventilation should be corrosion
proof. Make up air should be supplied to balance air that is removed by local or general exhaust
ventilation. Ventilate low lying areas such as sumps or pits where dense vapours may collect.
Engineering Controls:
PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Safety glasses with side shields are recommended as minimal eye protection. Use full face-shield or
chemical safety goggles when there is potential for contact. Contact lenses should not be worn when
working with this material.
Eye Protection:
Gloves and protective clothing made from PVC, butyl rubber, natural rubber, viton or neoprene should
be impervious under conditions of use. Prior to use, user should confirm impermeability. Discard
contaminated gloves.
Skin Protection:
No specific guidelines available. A NIOSH/MSHA-approved air-purifying respirator equipped with
organic vapour cartridges for concentrations up to 200 ppm. An air-supplied respirator if concentrations
are higher or unknown.
If while wearing a respiratory protection, you can smell, taste or otherwise detect anything unusual, or in
the case of a full facepiece respirator you experience eye irritation, leave the area immediately. Check
to make sure the respirator to face seal is still good. If it is, replace the filter, cartridge or canister. If
the seal is no longer good, you may need a new respirator. (4)
Respiratory Protection:
Wear an impermeable apron and boots. Locate safety shower and eyewash station close to chemical
handling area. Take all precautions to avoid personal contact.
Triethylene Glycol : Manufacturer's Recommended Exposure Level : 100 mg/m³ ( TWA ). (3)
Other Personal Protective
Equipment:
None established for this product.
EXPOSURE GUIDELINES
Liquid.
Clear, colourless liquid.
Mild, sweet odour.
Not available.
> 100 - 287.
-33 - - 7.2.
< 0.01.
5.2.
50%: 1.08; 55%: 1.09; 60%: 1.10; 80%: 1.113; 90%: 1.121; 100%: 1.127.
1 080 - 1 127 kg/m3.
Not available.
< 0.001.
Soluble in water. Hygroscopic.
< 50 %.
6.0 - 12.0 (1% IPA/water 50/50 v/v).
Not available.
Not available.
Physical State:
Appearance:
Odour:
Odour Threshold (ppm):
Boiling Range (°C):
Melting/Freezing Point (°C):
Vapour Pressure (mm Hg at 20° C):
Vapour Density (Air = 1.0):
Relative Density (g/cc):
Bulk Density:
Viscosity:
Evaporation Rate (Butyl Acetate = 1.0):
Solubility:
% Volatile by Volume:
pH:
Coefficient of Water/Oil Distribution:
Volatile Organic Compounds (VOC):
9. PHYSICAL AND CHEMICAL PROPERTIES (Not intended as Specifications)
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY
Stable.
Under Normal Conditions:
Not flammable. Not normally a fire hazard. Water content of product prevents ignition.
Under Fire Conditions:
Will not occur.
Hazardous Polymerization:
High temperatures, sparks, open flames and all other sources of ignition. Keep tightly closed to protect
quality. Avoid moisture contamination. Hygroscopic.
Conditions to Avoid:
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 6 of 8
11. TOXICOLOGICAL INFORMATION
TOXICOLOGICAL DATA:
SUBSTANCE
LD50 (Oral, Rat)
LD50 (Dermal, Rabbit)
LC50 (Inhalation, Rat, 4h)
Triethylene Glycol
2 206 - 17 000 mg/kg (1,3)
> 20 000 mg/kg (1)
---
Morpholine Derivatives
---
---
>5 000 ppm (3)
The ingredient(s) of this product is (are) not classed as carcinogenic by ACGIH, IARC, OSHA or NTP.
Carcinogenicity Data:
Not available. No adverse reproductive effects are anticipated.
Reproductive Data:
Not available. No adverse mutagenic effects are anticipated.
Mutagenicity Data:
Not available. No adverse teratogenic effects are anticipated.
Teratogenicity Data:
Morpholine Derivatives may cause skin sensitization or other allergic responses. Sensitization is the
process whereby a biological change occurs in the individual because of previous exposure to a
substance and, as a result, the individual reacts more strongly when subsequently exposed to the
substance. Once sensitized, an individual can react to extremely low airborne levels, even below the
TLV, or to skin contact. Cross sensitization may occur by skin contact with this material and other
amines.
Respiratory / Skin Sensitization
Data:
Morpholine Derivatives : This product contains an amine, which may react with nitrites to form a
nitrosamine. Some nitrosamines have been shown to be carcinogenic in laboratory animals.
Synergistic Materials:
Triethylene Glycol was given to rats by inclusion in the diet for 90 days at concentrations of 10,000,
20,000, or 50,000 ppm. At the highest dose, there were decreases in body weight. Physiologic
responses to these high doses were observed in kidney weight and urinalysis. No specific organ
toxicity was seen. (3)
In a 9-day (whole body) repeated exposure (6 h/day) study with rats, mortality occurred at 4,284
mg/M3 and effects included eye irritation and increased alanine aminotransferase and alkaline
phosphatase activities; at 494 mg/M3, there was slightly increased alkaline phosphatase activity. (3)
In a sensory irritation study in mice, exposure to high concentrations of Triethylene Glycol aerosol
resulted in decreased respiratory rate. The RD50, or concentration that produced a 50% decrease in
respiratory rate, was 5.1 mg/L. (3)
Other Studies Relevant to
Material:
12. ECOLOGICAL INFORMATION
Not available. Low acute toxicity to aquatic organisms.
Ecotoxicity:
Not available. Do not contaminate domestic or irrigation water supplies, lakes, streams, ponds, or
rivers. This product is biodegradable. Triethylene Glycol : has high mobility in soil. Triethylene Glycol is
estimated to have a low potential to bioconcentrate. (3)
Environmental Fate:
13. DISPOSAL CONSIDERATIONS
Neutralize carefully with weak acid to a pH of 6 to 9. Neutralization is expected to be exothermic.
Effervescence may result. Add a liberal covering of sodium bicarbonate. Confirm pH using pH paper.
Deactivating Chemicals:
This information applies to the material as manufactured. Reevaluation of the product may be required
by the user at the time of disposal since the product uses, transformations, mixtures and processes
may influence waste classification. Dispose of waste material at an approved (hazardous) waste
treatment/disposal facility in accordance with applicable local, provincial and federal regulations. Do not
dispose of waste with normal garbage, or to sewer systems.
Waste Disposal Methods:
See "Deactivating Chemicals". Rinse empty container three times with water
Safe Handling of Residues:
Strong oxidizing and reducing agents. Lewis or mineral acids. Strong bases. Isocyanates. Materials
reactive with hydroxyl bearing compounds. Fluorine. Solutions are slightly corrosive to metals.
Aluminum and its alloys.
Materials to Avoid:
Thermal decomposition products are toxic and may include oxides of carbon, nitrogen and irritating
gases. Heating in air may produce irritating aldehydes, acids and ketones.
Decomposition or Combustion
Products:
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 7 of 8
Empty containers retain product residue and can be hazardous. Empty drums should be completely
drained, properly bunged and promptly returned to a drum reconditioner. Treat package in the same
manner as the product.
Disposal of Packaging:
14. TRANSPORTATION INFORMATION
CANADIAN TDG ACT SHIPPING DESCRIPTION:
This product is not regulated by TDG.
Label(s): Not applicable. Placard: Not applicable.
ERAP Index: -----.
Exemptions: None known.
US DOT CLASSIFICATION (49CFR 172.101, 172.102):
This product is not regulated by DOT.
Label(s): Not applicable. Placard: Not applicable.
CERCLA-RQ: Not available.
Exemptions: None known.
15. REGULATORY INFORMATION
CANADA
All constituents of this product are included on the DSL.
CEPA - NSNR:
None known.
CEPA - NPRI:
Controlled Products Regulations Classification (WHMIS):
D-2B: Toxic (skin sensitizer)
E: Corrosive
USA
All constituents of this product are included on the TSCA inventory.
Environmental Protection Act:
Skin Sensitizer, Corrosive.
OSHA HCS (29CFR 1910.1200):
Text22:
NFPA: 1 Health, 1 Fire, 0 Reactivity (3)
Text22:
HMIS: 1 Health, 1 Fire, 0 Reactivity (3)
INTERNATIONAL
Not available.
16. OTHER INFORMATION
REFERENCES
RTECS-Registry of Toxic Effects of Chemical Substances, Canadian Centre for Occupational Health and Safety RTECS
database.
1.
Clayton, G.D. and Clayton, F.E., Eds., Patty's Industrial Hygiene and Toxicology, 3rd ed., Vol. IIA,B,C, John Wiley and Sons,
New York, 1981.
2.
Supplier's Material Safety Data Sheet(s).
3.
CHEMINFO, through "CCINFOdisc", Canadian Centre for Occupational Health and Safety, Hamilton, Ontario, Canada.
4.
Guide to Occupational Exposure Values, 2005, American Conference of Governmental Industrial Hygienists, Cincinnati, 2005.
5.
Regulatory Affairs Group, Brenntag Canada Inc.
6.
The British Columbia Drug and Poison Information Centre, Poison Managements Manual, Canadian Pharmaceutical
Association, Ottawa, 1981.
7.
NFPA 325M Fire Hazard Properties of Flammable Liquids, Gases, and Volatile Solids, 1994 Edition, Quincy, MA, 1994.
8.
____________________________________________________________________________________________________________
The information contained herein is offered only as a guide to the handling of this specific material and has been prepared in good faith
by technically knowledgeable personnel. It is not intended to be all-inclusive and the manner and conditions of use and handling may
involve other and additional considerations. No warranty of any kind is given or implied and Brenntag Canada Inc. will not be liable for
any damages, losses, injuries or consequential damages which may result from the use of or reliance on any information contained
Triethylene Glycol Inhibited to 5 % CFT1755CW
Brenntag Canada Inc.
Date of Revision: 2007 September 07
WHMIS Number :
00063338
Page 8 of 8
herein. This Material Safety Data Sheet is valid for three years.
____________________________________________________________________________________________________________
To obtain revised copies of this or other Material Safety Data Sheets, contact your nearest Brenntag Canada Regional office.
British Columbia: 20333-102B Avenue, Langley, BC, V1M 3H1
Phone: (604) 513-9009 Facsimile: (604) 513-9010
Alberta: 6628 - 45 th. Street, Leduc, AB, T9E 7C9
Phone: (780) 986-4544 Facsimile: (780) 986-1070
Manitoba: 681 Plinquet Street, Winnipeg, MB, R2J 2X2
Phone: (204) 233-3416 Facsimile: (204) 233-7005
Ontario: 43 Jutland Road, Toronto, ON, M8Z 2G6
Phone: (416) 259-8231 Facsimile: (416) 259-5333
Quebec: 2900 Jean Baptiste Des., Lachine, PQ, H8T 1C8
Phone: (514) 636-9230 Facsimile: (514) 636-0877
Atlantic: A-105 Akerley Boulevard, Dartmouth, NS, B3B 1R7
Phone: (902) 468-9690 Facsimile: (902) 468-3085
____________________________________________________________________________________________________________
Prepared By: Regulatory Affairs Group, Brenntag Canada Inc., (416) 259-8231.