MATERIAL SAFETY DATA SHEET
PROPELLANT A31 / ISOPENTANE BLENDS
3. HAZARDS IDENTIFICATION
High vapour concentrations may cause drowsiness. Gas reduces oxygen available for breathing. See
"Other Health Effects" Section. Flammable gas. Contents under pressure. Can decompose at high
temperatures forming toxic gases.
EMERGENCY OVERVIEW:
POTENTIAL HEALTH EFFECTS
EMERGENCY TELEPHONE NUMBERS (FOR EMERGENCIES INVOLVING CHEMICAL SPILLS OR RELEASE)
Toronto, ON (416) 226-6117 Montreal, QC (514) 861-1211 Winnipeg, MB (204) 943-8827
Edmonton, AB (780) 424-1754 Calgary, AB (403) 263-8660 Vancouver, BC (604) 685-5036
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Brenntag Canada Inc.
43 Jutland Rd.
Toronto, ON
M8Z 2G6
(416) 259-8231
Website: http:\\www.brenntag.ca
WHMIS#:
00062278
Index:
2009 January 13
PRODUCT IDENTIFICATION
Propellant A31 / Isopentane Blends.
Product Name:
2009 January 13
Date of Revision:
Effective Date:
HCI1136/09A
Not available.
Chemical Name:
Propellant A31 / Isopentane 2575; Propellant A31 / Isopentane 2080;
Propellant A31 / Isopentane 8515; Propellant A31 / Isopentane 0595; Propellant.
Synonyms:
Paraffin Series Hydrocarbon.
Chemical Family:
C4H10 / C5H12.
Molecular Formula:
Propellant Blend.
Product Use:
WHMIS Classification / Symbol:
READ THE ENTIRE MSDS FOR THE COMPLETE HAZARD EVALUATION OF THIS PRODUCT.
A: Compressed Gas
B-1: Flammable Gas
Ingredient
CAS#
ACGIH TLV
% Concentration
2. COMPOSITION, INFORMATION ON INGREDIENTS (Not Intended As Specifications)
Liquefied petroleum gas
68476-85-7
1000 ppm
100

2-Methyl Butane
78-78-4
600 ppm
---
Isobutane
75-28-5
1000 ppm
---

For product composition see SECTION
16 "OTHER INFORMATION".
---
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 2 of 8
4. FIRST AID MEASURES
FIRST AID PROCEDURES
Move victim to fresh air. Give artificial respiration ONLY if breathing has stopped. Give cardiopulmonary
resuscitation (CPR) if there is no breathing AND no pulse. Obtain medical attention IMMEDIATELY.
Inhalation:
Treat frostbite by immediately immersing affected areas in warm water until the skin has warmed up and
turned pink. Obtain medical attention IMMEDIATELY.
Skin Contact:
Immediately flush eyes with running water for a minimum of 20 minutes. Hold eyelids open during
flushing. If irritation persists, repeat flushing. Obtain medical attention IMMEDIATELY.
Eye Contact:
Do not attempt to give anything by mouth to an unconscious person. If victim is alert and not convulsing,
rinse mouth out and give 1/2 to 1 glass of water to dilute material. DO NOT induce vomiting. If
spontaneous vomiting occurs, have victim lean forward with head down to avoid breathing in of vomitus,
rinse mouth and administer more water. Obtain medical attention IMMEDIATELY.
Ingestion:
When treating frost bite or exposure to the cooling effects of liquid gas contact, flush affected areas with
water no warmer than 44 Deg. Celsius. Do not use heated water or dry heat and frozen parts should not
be rubbed before or after thawing.
Freeze burns of mucosal tissue can develop following contact with liquid form of this material.
2-methyl butane or iso-Butane: Vasopressor drugs (e.g. epinephrine, ephedrine etc.) should not be given
on their own as there may be danger of cardiac arrhythmia. (7)
Medical conditions that may be aggravated by exposure to this product include diseases of the skin,
eyes or respiratory tract.
Note to Physicians:
This product, when present in high concentrations in air, acts primarily as a simple asphyxiant without
other significant effects. Product may be mildly irritating to the nose, throat and respiratory tract and may
cause coughing and sneezing. See "Other Health Effects" Section. Product is not odourized. Poor
warning properties.
Inhalation:
Rapid evaporation may cause frostbite. Evaporation of liquid from the skin can produce chilling
sensation. Skin injury does not result.
Skin Contact:
Systemic toxic concentrations are unlikely to be absorbed through the skin in humans.
Skin Absorption:
The liquid of this material can produce chilling sensation and discomfort. This product causes irritation,
redness and pain. See "Other Health Effects" Section.
Eye Contact:
Product is a gas. Ingestion is not a likely route of exposure.
Ingestion:
May cause cardiac arrhythmia, irregular, rapid breathing, asphyxiation and central nervous system
(CNS) depression. 2-methyl butane or iso-Butane may sensitize heart muscle causing cardiac
arrhythmia, in rare cases. CNS depression is characterized by headache, dizziness, drowsiness,
nausea, vomiting and incoordination. Severe overexposures may lead to coma and possible death due
to respiratory failure.
Simple Asphyxiants - "Inert" Gases or Vapours: A number of gases and vapours, when present in high
concentrations in air, act primarily as simple asphyxiants without other significant physiologic effects. A
TLV may not be recommended for each simple asphyxiant because the limiting factor is the available
oxygen. The minimal oxygen content should be 18 % by volume under normal atmospheric pressure
(equivalent to a partial pressure of 135 Torr). Atmospheres deficient in oxygen do not provide adequate
warning and most simple asphyxiants are odourless. Several simple asphyxiants present an explosion
hazard. (2)
Asphyxia is characterized by increased breathing volume, accelerated pulse rate, muscular
incoordination, faulty judgement, emotional instability, fatigue, nausea, vomiting, bewilderment, gasping
respiration and unconsciousness.
Other Health Effects:
5. FIRE-FIGHTING MEASURES
Flashpoint (°C)
AutoIgnition
Temperature (°C)
LEL
UEL
Flammability Limits in Air (%):
- 82.6. (3)
420. (Estimated)
1.4. (3)
8.4. (3)
B-1: Flammable Gas
Flammability Class (WHMIS):
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 3 of 8
Thermal decomposition products are toxic and may include oxides of carbon.
Hazardous Combustion
Products:
Vapours from this product are heavier than air, and may "travel" to a source of ignition (eg. pilot lights,
heaters, electric motors) some distance away, and then "flash back" to the point of product discharge
causing an explosion and fire.
Expansion of liquid and change of state from liquid to vapour will allow combustible mixture to
encompass a large area. If tank is involved in a fire situation, a BLEVE (Boiling Liquid Expanding Vapour
Explosion) may result. Enforce NO SMOKING rules.
Unusual Fire or Explosion
Hazards:
Not expected to be sensitive to mechanical impact.
Sensitivity to Mechanical Impact:
Not available.
Rate of Burning:
Not available.
Explosive Power:
Expected to be sensitive to static discharge when vapours are present between the lower and upper
explosive limits.
Sensitivity to Static Discharge:
EXTINGUISHING MEDIA
Do not extinguish flame unless leak can be stopped immediately. Use carbon dioxide or dry chemical
media for small fires. If only water is available, use it in the form of a fog.
Fire Extinguishing Media:
FIRE FIGHTING
INSTRUCTIONS
Expansion of liquid and change of state from liquid to vapour will allow combustible mixture to
encompass a large area. Where possible, shut off supply flow of gas. When fighting fires involving
flammable gases, the best procedure is to stop the flow of gas before trying to extinguish the fire.
Extinguishing the fire while there is a continuous flow of gas is dangerous and could lead to the
formation of an explosive mixture with air. Should re-ignition of this mixture occur, there is a potential for
greater damage than if the original fire had been allowed to burn. Under certain circumstances,
extinguishing the fire with carbon dioxide or dry chemical powder may be necessary to permit access to
the valves to shut off the flow of gas. If it is not possible to shut the flow of gas off and there is no risk to
the surrounding area, it is preferable to let the fire burn, while protecting adjacent material with water
spray until the flow can be stopped. (4)
Gas clouds may be controlled with the use of water spray or fog. Isolate materials that are not involved
in the fire and protect personnel. The heat from a fire can cause a build-up of pressure inside the
cylinders, which may explode and rupture. Any cylinders in the area should be removed, provided it can
be done without risk. Fire exposed cylinders can be kept cool by spraying water. No part of a cylinder
should be exposed to temperatures above 52 Degrees Celsius. (4)
For massive fires, used unmanned hose holders and monitor nozzles. If this is not possible, withdraw
from the fire area and allow fire to burn. Avoid standing near the ends of tanks. If a rising sound is
heard from the venting safety device or discolouration of the tanks have occurred, WITHDRAW
IMMEDIATELY. (4) The possibility of an explosive atmosphere exists, after the fire has been
extinguished. Before entering such an area, check the atmosphere with an appropriate device. (4)
Instructions to the Fire Fighters:
Propellant gases can displace oxygen, therefore reducing the amount of oxygen available for breathing.
Firefighters can enter the area if a positive pressure self-contained breathing apparatus and full bunker
gear are worn. (4)
Fire Fighting Protective
Equipment:
6. ACCIDENTAL RELEASE MEASURES
Information in this section is for responding to spills, leaks or releases in order to prevent or minimize the adverse effects on persons,
property and the environment. There may be specific reporting requirements associated with spills, leaks or releases, which change from
region to region.
In all cases of leak or spill contact vendor at Emergency Number shown on the front page of this MSDS.
Ventilate enclosed spaces. Eliminate all sources of ignition. Notify applicable government authority if
release is reportable or could adversely affect the environment. For large spills, warn general public of
potential flash-back of flammable vapours. Move unprotected personnel upwind of leaking container.
Call emergency response naming the chemical and the type of container that is leaking. Consider the
use of fog-nozzles to control vapours. Do not immerse in water. Where possible, elevate the leak to the
highest position of the cylinder, such that gas and not liquid escapes. Apply emergency device. Ventilate
low lying areas such as sumps or pits where dense vapours may collect.
Containment and Clean-Up
Procedures:
7. HANDLING AND STORAGE
HANDLING
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 4 of 8
Ground and bond equipment and containers to prevent a static charge buildup. Use spark-resistant
tools. Use normal "good" industrial hygiene and housekeeping practices. Enforce NO SMOKING rules in
area of use. Secure containers at all times. Fix leaks promptly.
Caps should always be placed on cylinders until ready for use. Always secure cylinders to a wall, rack or
other solid structure in an upright position. Do not handle cylinders with oily hands. Do not use cylinder
if damaged. Use an appropriate pressure regulator. Before connecting the cylinder, make sure that
back feed from the system to the cylinder is prevented. The valve should be opened slowly to prevent
rapid decompression and damage to the valve. Make sure the valves on the gas cylinder is fully opened
when gas is in use. The valves should be opened and closed at least once a day, while in use, to
prevent freezing. (4)
Vapours are heavier than air. Vapours can create a suffocating atmosphere, which may be fatal. Use
self-contained breathing apparatus. Ground and bond equipment and containers to prevent a static
charge buildup. Use spark-resistant tools. Enforce NO SMOKING rules in area of use.
Handling Practices:
Ventilation should be explosion proof.
Ventilation Requirements:
Use only with adequate ventilation and avoid breathing gas, aerosols, vapours or mists. Avoid contact
with eyes, skin or clothing. Wash thoroughly with soap and water after handling. Wash contaminated
clothing thoroughly before re-use.
Expansion of liquid and change of state from liquid to vapour will allow combustible mixture to
encompass a large area. Cylinders should not be lifted by the cap or by lifting magnets. Shut flow off at
cylinder valve and not just the regulator after use. Replace outlet caps or plugs and cylinder caps as
soon as the cylinder is disconnected from equipment. The empty cylinders should be kept under slightly
positive pressure. Regularly check the cylinders for corrosion or leakage. (4)
Other Precautions:
STORAGE
Ideal storage temperature is 10-27 Deg. Celsius.
Storage Temperature (°C):
See below.
Ventilation Requirements:
Store in a cool, well-ventilated area. Keep away from heat, sparks and flames. Keep containers closed.
Do not expose sealed containers to temperatures above 40° C. Protect from direct sunlight. Protect
against physical damage. Secure containers at all times. Keep away from combustibles and
incompatible materials. Regularly inspect process equipment, piping and detection equipment. Fix leaks
promptly.
Check to see if the cylinders have been tested within the required time. Check compatibility with other
materials and separate at appropriate distance. Empty cylinders should be stored separately from full
ones, with valves off, securely capped and clearly labeled EMPTY. (4)
Storage Requirements:
Confirm suitability of any material before using.
Special Materials to be Used for
Packaging or Containers:
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Recommendations listed in this section indicate the type of equipment, which will provide protection against overexposure to this product.
Conditions of use, adequacy of engineering or other control measures, and actual exposures will dictate the need for specific protective
devices at your workplace.
ENGINEERING CONTROLS
Local exhaust ventilation required. Ventilation should be explosion proof. Ventilate low lying areas such
as sumps or pits where dense vapours may collect. Make up air should be supplied to balance air that is
removed by local or general exhaust ventilation.
For personnel entry into confined spaces (i.e. bulk storage tanks) a proper procedure must be followed.
It must include consideration of, among other things, ventilation, testing of tank atmosphere, provision
and maintenance of SCBA, and emergency rescue. Use the "buddy" system. The second person should
be in view and trained and equipped to execute a rescue. (4)
Engineering Controls:
PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Safety glasses with side shields are recommended to prevent eye contact. Use chemical safety goggles
when there is potential for eye contact. Contact lenses should not be worn when working with this
material.
Eye Protection:
Skin protection should be insulated against cold temperatures. Discard contaminated gloves. Prior to
use, user should confirm impermeability.
Skin Protection:
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 5 of 8
Do not use compressed oxygen in hydrocarbon atmospheres. A NIOSH/MSHA-approved air-supplied
respirator for atmospheres (normal atmospheric pressure) containing less than 18% oxygen by volume.
Immediately Dangerous to Life and Health (IDLH) value: 1500 ppm Isopentane. The purpose of
establishing an IDLH value is to ensure that the worker can escape from a given contaminated
environment in the event of failure of the most protective respiratory equipment. In the event of failure of
respiratory protective equipment, every effort should be made to exit immediately. (4)
If while wearing a respiratory protection, you can smell, taste or otherwise detect anything unusual, or in
the case of a full facepiece respirator you experience eye irritation, leave the area immediately. Check to
make sure the respirator to face seal is still good. If it is, replace the filter, cartridge or canister. If the
seal is no longer good, you may need a new respirator. (4)
Respiratory Protection:
Wear regular work clothing. The use of coveralls is recommended. Locate safety shower and eyewash
station close to chemical handling area. Take all precautions to avoid personal contact. Clothing and
footwear that is fire retardant and dissipates static electrical charges should be worn when handling
flammable materials. Natural fibers (cotton, wool, leather and linen) should be selected in favour of
synthetic materials (rayon, nylon and polyester).
Other Personal Protective
Equipment:
EXPOSURE GUIDELINES
SUBSTANCE
ACGIH TLV
(STEL)
OSHA PEL
(TWA) (STEL)
NIOSH REL
(TWA) (STEL)
Liquefied petroleum gas
—
1000 ppm
---
1000 ppm
---
2-Methyl Butane
—
1000 ppm
---
120 ppm
610 ppm (Ceiling)
Isobutane
—
---
---
800 ppm
---
Gas.
Colourless liquified gas.
Hydrocarbon odour.
Not available.
-1.17 to 28.8.
Not available.
1 117 to 2 156 at 21 °C.
2.1 - 2.5.
0.57 to 0.62.
Not available.
Not available.
> 1.
0 - 0.008 % in water. (3)
100%.
Not applicable.
Not available.
100%.
Physical State:
Appearance:
Odour:
Odour Threshold (ppm):
Boiling Range (°C):
Melting/Freezing Point (°C):
Vapour Pressure (mm Hg at 20° C):
Vapour Density (Air = 1.0):
Relative Density (g/cc):
Bulk Density:
Viscosity:
Evaporation Rate (Butyl Acetate = 1.0):
Solubility:
% Volatile by Volume:
pH:
Coefficient of Water/Oil Distribution:
Volatile Organic Compounds (VOC):
9. PHYSICAL AND CHEMICAL PROPERTIES (Not intended as Specifications)
- 82.6. (3)
Flashpoint (°C):
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY
Stable.
Under Normal Conditions:
Flammable. May rupture process equipment as pressure increases with elevated temperature. High risk
of BLEVE (Boiling Liquid Expanded Vapour Explosion).
Under Fire Conditions:
Will not occur.
Hazardous Polymerization:
High temperatures, sparks, open flames and all other sources of ignition. Avoid extended contact with air
or oxygen.
Conditions to Avoid:
Strong oxidizers. Lewis or mineral acids. Alkali metals and their hydroxides. Liquid Oxygen. Peroxides.
Materials to Avoid:
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 6 of 8
11. TOXICOLOGICAL INFORMATION
TOXICOLOGICAL DATA:
SUBSTANCE
LD50 (Oral, Rat)
LD50 (Dermal, Rabbit)
LC50 (Inhalation, Rat, 4h)
2-Methyl Butane
---
---
280 000 mg/m3 (1)
Isobutane
---
---
658 000 mg/kg (1)
The ingredient(s) of this product is (are) not classed as carcinogenic by ACGIH, IARC, OSHA or NTP.
Carcinogenicity Data:
No information is available and no adverse reproductive effects are anticipated. See "Other Studies
Relevant to Material".
Reproductive Data:
No information is available and no adverse mutagenic effects are anticipated.
Mutagenicity Data:
No information is available and no adverse teratogenic/embryotoxic effects are anticipated.
Teratogenicity Data:
None known.
Respiratory / Skin Sensitization
Data:
None known.
Synergistic Materials:
iso-Butane: A formulation containing 83.2 % Isobutane applied to the skin caused moderate irritation.
However, application of other formulations containing 74.25 to 89.55 % only caused mild irritation. Mice
exposed to Isobutane concentrations of 15 %, 20 % and 23 % showed signs of anesthesia within 60, 17
and 26 minutes respectively. Exposure to 10 to 20 % in monkeys did not cause circulatory effects, but
did depress respiratory function. Isobutane is a week cardiac sensitizer in dogs and rats. (4)
2-methyl butane: In a study involving skin contact with an unspecifed Pentane isomer, 1.5 ml was
applied to the forearm for one hour and the thigh for five hours. This resulted in a burning sensation with
itching and the effects subsided within fifteen minutes after exposure. (4)
Exposure to 120,000 ppm Isopentane produced light anesthesia to dogs while 150,000 to 170,000 ppm
Isopentane was lethal. Light anesthesia was observed in mice when exposed to 90,000 ppm
Isopentane, while 100,000 to 120,000 ppm caused anesthesia in four minutes with complete loss of
posture within 10 minutes. Sensitization of the heart to the effects of epinephrine causing cardiac
arrythmias were observed at 100,000 to 250,000 ppm. (4)
Other Studies Relevant to
Material:
12. ECOLOGICAL INFORMATION
Not available. May be harmful to aquatic life.
Ecotoxicity:
Not available. Volatalizes rapidly. Do not contaminate domestic or irrigation water supplies, lakes,
streams, ponds, or rivers.
Environmental Fate:
13. DISPOSAL CONSIDERATIONS
None required.
Deactivating Chemicals:
This information applies to the material as manufactured. Reevaluation of the product may be required
by the user at the time of disposal since the product uses, transformations, mixtures and processes may
influence waste classification. Dispose of waste material at an approved (hazardous) waste
treatment/disposal facility in accordance with applicable local, provincial and federal regulations. Do not
dispose of waste with normal garbage, or to sewer systems.
Waste Disposal Methods:
Flare off vapours at safe locations.
Safe Handling of Residues:
Empty containers retain product residue (liquid and/or vapour) and can be dangerous. Do not expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition; they may explode
and cause injury or death. Return empty containers.
Disposal of Packaging:
14. TRANSPORTATION INFORMATION
CANADIAN TDG ACT SHIPPING DESCRIPTION:
Thermal decomposition products are toxic and may include oxides of carbon.
Decomposition or Combustion
Products:
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 7 of 8
SEE BELOW
Label(s): Not applicable. Placard: Not applicable.
ERAP Index: -----.
Exemptions: None known.
Propellant A31 / Isopentane 05 / 95:
FLAMMABLE LIQUID, N.O.S. (Isobutane, Isopentane), Not Odourized, Class 3, UN1993, PG I.
Propellant A31 / Isopentane 25 / 75; Propellant A31 / Isopentane 20 / 80; Propellant A31 / Isopentane 85 / 15:
LIQUEFIED GAS, FLAMMABLE, N.O.S. (Isobutane, Isopentane), Not Odourized, Class 2.1, UN3161.
US DOT CLASSIFICATION (49CFR 172.101, 172.102):
SEE BELOW
Label(s): Not applicable. Placard: Not applicable.
CERCLA-RQ: Not available.
Exemptions: None known.
Propellant A31 / Isopentane 05 / 95:
FLAMMABLE LIQUID, N.O.S. (Isobutane, Isopentane), Not Odourized, Class 3, UN1993, PG I.
Propellant A31 / Isopentane 25 / 75; Propellant A31 / Isopentane 20 / 80; Propellant A31 / Isopentane 85 / 15:
LIQUEFIED GAS, FLAMMABLE, N.O.S. (Isobutane, Isopentane), Not Odourized, Class 2.1, UN3161.
15. REGULATORY INFORMATION
CANADA
All constituents of this product are included on the DSL.
CEPA - NSNR:
Not included.
CEPA - NPRI:
Controlled Products Regulations Classification (WHMIS):
16. OTHER INFORMATION
ADDITIONAL INFORMATION
Product A31 (Isobutane) Isopentane
(wt %) (wt %)
A-31 /I sopentane (0595) 05 95
A-31 / Isopentane (2080) 20 80
A-31 / Isopentane (2575) 25 75
A-31 /I sopentane (8515) 85 15
USA
All constituents of this product are included on the TSCA inventory.
Environmental Protection Act:
Compressed Gas. Flammable Gas.
OSHA HCS (29CFR 1910.1200):
Text22:
NFPA: 1 Health, 4 Fire, 1 Reactivity (6)
Text22:
HMIS: 1 Health, 4 Fire, 1 Reactivity (3)
INTERNATIONAL
2-methyl butane and iso-Butane are found on the following inventories: EINECS (European Inventory of Existing Commercial Chemical
Substances).
A: Compressed Gas
B-1: Flammable Gas
Propellant A31 / Isopentane Blends
Brenntag Canada Inc.
Date of Revision:
2009 January 13
WHMIS Number :
00062278
Page 8 of 8
REFERENCES
RTECS-Registry of Toxic Effects of Chemical Substances, Canadian Centre for Occupational Health and Safety RTECS
database.
1.
Clayton, G.D. and Clayton, F.E., Eds., Patty's Industrial Hygiene and Toxicology, 3rd ed., Vol. IIA,B,C, John Wiley and Sons, New
York, 1981.
2.
Supplier's Material Safety Data Sheet(s).
3.
CHEMINFO, through "CCINFOdisc", Canadian Centre for Occupational Health and Safety, Hamilton, Ontario, Canada.
4.
Guide to Occupational Exposure Values, 2007, American Conference of Governmental Industrial Hygienists, Cincinnati, 2007.
5.
Regulatory Affairs Group, Brenntag Canada Inc.
6.
The British Columbia Drug and Poison Information Centre, Poison Managements Manual, Canadian Pharmaceutical Association,
Ottawa, 1981.
7.
____________________________________________________________________________________________________________
The information contained herein is offered only as a guide to the handling of this specific material and has been prepared in good faith by
technically knowledgeable personnel. It is not intended to be all-inclusive and the manner and conditions of use and handling may involve
other and additional considerations. No warranty of any kind is given or implied and Brenntag Canada Inc. will not be liable for any
damages, losses, injuries or consequential damages which may result from the use of or reliance on any information contained herein.
This Material Safety Data Sheet is valid for three years.
____________________________________________________________________________________________________________
To obtain revised copies of this or other Material Safety Data Sheets, contact your nearest Brenntag Canada Regional office.
British Columbia: 20333-102B Avenue, Langley, BC, V1M 3H1
Phone: (604) 513-9009 Facsimile: (604) 513-9010
Alberta: 6628 - 45 th. Street, Leduc, AB, T9E 7C9
Phone: (780) 986-4544 Facsimile: (780) 986-1070
Manitoba: 681 Plinquet Street, Winnipeg, MB, R2J 2X2
Phone: (204) 233-3416 Facsimile: (204) 233-7005
Ontario: 43 Jutland Road, Toronto, ON, M8Z 2G6
Phone: (416) 259-8231 Facsimile: (416) 259-5333
Quebec: 2900 Jean Baptiste Des., Lachine, PQ, H8T 1C8
Phone: (514) 636-9230 Facsimile: (514) 636-0877
Atlantic: A-105 Akerley Boulevard, Dartmouth, NS, B3B 1R7
Phone: (902) 468-9690 Facsimile: (902) 468-3085
____________________________________________________________________________________________________________
Prepared By: Regulatory Affairs Group, Brenntag Canada Inc., (416) 259-8231.